Discussion:
[PATCH 0/3] i2c/at91: add support PM functions
Wenyou Yang
2014-10-20 03:42:11 UTC
Permalink
Hi Wolfram,

The patches is to add support to PM functions for the at91 i2c controller.

It is based on the i2c/for-next branch of
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux.git.

Could you help review it?

Best Regards,
Wenyou Yang

Wenyou Yang (3):
i2c/at91: add support for runtime PM
i2c/at91: add support for system PM
i2c/at91: adopt pinctrl support

drivers/i2c/busses/i2c-at91.c | 86 ++++++++++++++++++++++++++++++++++++-----
1 file changed, 77 insertions(+), 9 deletions(-)
--
1.7.9.5
Wenyou Yang
2014-10-20 03:42:12 UTC
Permalink
Drivers should put the device into low power states proactively whenever the
device is not in use. Thus implement support for runtime PM and use the
autosuspend feature to make sure that we can still perform well in case we see
lots of i2c traffic within short period of time.

Signed-off-by: Wenyou Yang <wenyou.yang-***@public.gmane.org>
---
drivers/i2c/busses/i2c-at91.c | 48 ++++++++++++++++++++++++++++++++---------
1 file changed, 38 insertions(+), 10 deletions(-)

diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c
index 917d545..03b9f48 100644
--- a/drivers/i2c/busses/i2c-at91.c
+++ b/drivers/i2c/busses/i2c-at91.c
@@ -31,10 +31,12 @@
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/platform_data/dma-atmel.h>
+#include <linux/pm_runtime.h>

#define DEFAULT_TWI_CLK_HZ 100000 /* max 400 Kbits/s */
#define AT91_I2C_TIMEOUT msecs_to_jiffies(100) /* transfer timeout */
#define AT91_I2C_DMA_THRESHOLD 8 /* enable DMA if transfer size is bigger than this threshold */
+#define AUTOSUSPEND_TIMEOUT 2000

/* AT91 TWI register definitions */
#define AT91_TWI_CR 0x0000 /* Control Register */
@@ -475,12 +477,16 @@ error:
static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num)
{
struct at91_twi_dev *dev = i2c_get_adapdata(adap);
- int ret;
+ int ret = 0;
unsigned int_addr_flag = 0;
struct i2c_msg *m_start = msg;

dev_dbg(&adap->dev, "at91_xfer: processing %d messages:\n", num);

+ ret = pm_runtime_get_sync(dev->dev);
+ if (ret < 0)
+ goto out;
+
/*
* The hardware can handle at most two messages concatenated by a
* repeated start via it's internal address feature.
@@ -488,18 +494,21 @@ static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num)
if (num > 2) {
dev_err(dev->dev,
"cannot handle more than two concatenated messages.\n");
- return 0;
+ ret = 0;
+ goto out;
} else if (num == 2) {
int internal_address = 0;
int i;

if (msg->flags & I2C_M_RD) {
dev_err(dev->dev, "first transfer must be write.\n");
- return -EINVAL;
+ ret = -EINVAL;
+ goto out;
}
if (msg->len > 3) {
dev_err(dev->dev, "first message size must be <= 3.\n");
- return -EINVAL;
+ ret = -EINVAL;
+ goto out;
}

/* 1st msg is put into the internal address, start with 2nd */
@@ -523,7 +532,13 @@ static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num)

ret = at91_do_twi_transfer(dev);

- return (ret < 0) ? ret : num;
+ if (ret == 0)
+ ret = num;
+out:
+ pm_runtime_mark_last_busy(dev->dev);
+ pm_runtime_put_autosuspend(dev->dev);
+
+ return ret;
}

static u32 at91_twi_func(struct i2c_adapter *adapter)
@@ -795,11 +810,20 @@ static int at91_twi_probe(struct platform_device *pdev)
dev->adapter.timeout = AT91_I2C_TIMEOUT;
dev->adapter.dev.of_node = pdev->dev.of_node;

+ pm_runtime_set_autosuspend_delay(dev->dev, AUTOSUSPEND_TIMEOUT);
+ pm_runtime_use_autosuspend(dev->dev);
+ pm_runtime_set_active(dev->dev);
+ pm_runtime_enable(dev->dev);
+
rc = i2c_add_numbered_adapter(&dev->adapter);
if (rc) {
dev_err(dev->dev, "Adapter %s registration failed\n",
dev->adapter.name);
clk_disable_unprepare(dev->clk);
+
+ pm_runtime_disable(dev->dev);
+ pm_runtime_set_suspended(dev->dev);
+
return rc;
}

@@ -814,16 +838,19 @@ static int at91_twi_remove(struct platform_device *pdev)
i2c_del_adapter(&dev->adapter);
clk_disable_unprepare(dev->clk);

+ pm_runtime_disable(dev->dev);
+ pm_runtime_set_suspended(dev->dev);
+
return 0;
}

#ifdef CONFIG_PM
-
+#ifdef CONFIG_PM_RUNTIME
static int at91_twi_runtime_suspend(struct device *dev)
{
struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);

- clk_disable(twi_dev->clk);
+ clk_disable_unprepare(twi_dev->clk);

return 0;
}
@@ -832,12 +859,13 @@ static int at91_twi_runtime_resume(struct device *dev)
{
struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);

- return clk_enable(twi_dev->clk);
+ return clk_prepare_enable(twi_dev->clk);
}
+#endif

static const struct dev_pm_ops at91_twi_pm = {
- .runtime_suspend = at91_twi_runtime_suspend,
- .runtime_resume = at91_twi_runtime_resume,
+ SET_RUNTIME_PM_OPS(at91_twi_runtime_suspend,
+ at91_twi_runtime_resume, NULL)
};

#define at91_twi_pm_ops (&at91_twi_pm)
--
1.7.9.5
Ludovic Desroches
2014-10-20 12:39:14 UTC
Permalink
Hi Wenyou,
Post by Wenyou Yang
Drivers should put the device into low power states proactively whenever the
device is not in use. Thus implement support for runtime PM and use the
autosuspend feature to make sure that we can still perform well in case we see
lots of i2c traffic within short period of time.
---
drivers/i2c/busses/i2c-at91.c | 48 ++++++++++++++++++++++++++++++++---------
1 file changed, 38 insertions(+), 10 deletions(-)
diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c
index 917d545..03b9f48 100644
--- a/drivers/i2c/busses/i2c-at91.c
+++ b/drivers/i2c/busses/i2c-at91.c
@@ -31,10 +31,12 @@
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/platform_data/dma-atmel.h>
+#include <linux/pm_runtime.h>
#define DEFAULT_TWI_CLK_HZ 100000 /* max 400 Kbits/s */
#define AT91_I2C_TIMEOUT msecs_to_jiffies(100) /* transfer timeout */
#define AT91_I2C_DMA_THRESHOLD 8 /* enable DMA if transfer size is bigger than this threshold */
+#define AUTOSUSPEND_TIMEOUT 2000
/* AT91 TWI register definitions */
#define AT91_TWI_CR 0x0000 /* Control Register */
static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num)
{
struct at91_twi_dev *dev = i2c_get_adapdata(adap);
- int ret;
+ int ret = 0;
Not necessary.
Post by Wenyou Yang
unsigned int_addr_flag = 0;
struct i2c_msg *m_start = msg;
dev_dbg(&adap->dev, "at91_xfer: processing %d messages:\n", num);
+ ret = pm_runtime_get_sync(dev->dev);
+ if (ret < 0)
+ goto out;
+
/*
* The hardware can handle at most two messages concatenated by a
* repeated start via it's internal address feature.
@@ -488,18 +494,21 @@ static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num)
if (num > 2) {
dev_err(dev->dev,
"cannot handle more than two concatenated messages.\n");
- return 0;
+ ret = 0;
+ goto out;
} else if (num == 2) {
int internal_address = 0;
int i;
if (msg->flags & I2C_M_RD) {
dev_err(dev->dev, "first transfer must be write.\n");
- return -EINVAL;
+ ret = -EINVAL;
+ goto out;
}
if (msg->len > 3) {
dev_err(dev->dev, "first message size must be <= 3.\n");
- return -EINVAL;
+ ret = -EINVAL;
+ goto out;
}
/* 1st msg is put into the internal address, start with 2nd */
@@ -523,7 +532,13 @@ static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num)
ret = at91_do_twi_transfer(dev);
- return (ret < 0) ? ret : num;
+ if (ret == 0)
I don't figure out why you've changed this condition.
Post by Wenyou Yang
+ ret = num;
+ pm_runtime_mark_last_busy(dev->dev);
+ pm_runtime_put_autosuspend(dev->dev);
+
+ return ret;
}
static u32 at91_twi_func(struct i2c_adapter *adapter)
@@ -795,11 +810,20 @@ static int at91_twi_probe(struct platform_device *pdev)
dev->adapter.timeout = AT91_I2C_TIMEOUT;
dev->adapter.dev.of_node = pdev->dev.of_node;
+ pm_runtime_set_autosuspend_delay(dev->dev, AUTOSUSPEND_TIMEOUT);
+ pm_runtime_use_autosuspend(dev->dev);
+ pm_runtime_set_active(dev->dev);
+ pm_runtime_enable(dev->dev);
+
rc = i2c_add_numbered_adapter(&dev->adapter);
if (rc) {
dev_err(dev->dev, "Adapter %s registration failed\n",
dev->adapter.name);
clk_disable_unprepare(dev->clk);
+
+ pm_runtime_disable(dev->dev);
+ pm_runtime_set_suspended(dev->dev);
+
return rc;
}
@@ -814,16 +838,19 @@ static int at91_twi_remove(struct platform_device *pdev)
i2c_del_adapter(&dev->adapter);
clk_disable_unprepare(dev->clk);
+ pm_runtime_disable(dev->dev);
+ pm_runtime_set_suspended(dev->dev);
+
return 0;
}
#ifdef CONFIG_PM
-
+#ifdef CONFIG_PM_RUNTIME
static int at91_twi_runtime_suspend(struct device *dev)
{
struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);
- clk_disable(twi_dev->clk);
+ clk_disable_unprepare(twi_dev->clk);
return 0;
}
@@ -832,12 +859,13 @@ static int at91_twi_runtime_resume(struct device *dev)
{
struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);
- return clk_enable(twi_dev->clk);
+ return clk_prepare_enable(twi_dev->clk);
}
+#endif
static const struct dev_pm_ops at91_twi_pm = {
- .runtime_suspend = at91_twi_runtime_suspend,
- .runtime_resume = at91_twi_runtime_resume,
+ SET_RUNTIME_PM_OPS(at91_twi_runtime_suspend,
+ at91_twi_runtime_resume, NULL)
};
#define at91_twi_pm_ops (&at91_twi_pm)
--
1.7.9.5
Regards

Ludovic
Ludovic Desroches
2014-10-20 13:14:12 UTC
Permalink
Adding Kevin in the CC list since he had some comments about the PM
runtime support for the SPI driver.
Post by Ludovic Desroches
Hi Wenyou,
Post by Wenyou Yang
Drivers should put the device into low power states proactively whenever the
device is not in use. Thus implement support for runtime PM and use the
autosuspend feature to make sure that we can still perform well in case we see
lots of i2c traffic within short period of time.
---
drivers/i2c/busses/i2c-at91.c | 48 ++++++++++++++++++++++++++++++++---------
1 file changed, 38 insertions(+), 10 deletions(-)
diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c
index 917d545..03b9f48 100644
--- a/drivers/i2c/busses/i2c-at91.c
+++ b/drivers/i2c/busses/i2c-at91.c
@@ -31,10 +31,12 @@
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/platform_data/dma-atmel.h>
+#include <linux/pm_runtime.h>
#define DEFAULT_TWI_CLK_HZ 100000 /* max 400 Kbits/s */
#define AT91_I2C_TIMEOUT msecs_to_jiffies(100) /* transfer timeout */
#define AT91_I2C_DMA_THRESHOLD 8 /* enable DMA if transfer size is bigger than this threshold */
+#define AUTOSUSPEND_TIMEOUT 2000
/* AT91 TWI register definitions */
#define AT91_TWI_CR 0x0000 /* Control Register */
static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num)
{
struct at91_twi_dev *dev = i2c_get_adapdata(adap);
- int ret;
+ int ret = 0;
Not necessary.
Post by Wenyou Yang
unsigned int_addr_flag = 0;
struct i2c_msg *m_start = msg;
dev_dbg(&adap->dev, "at91_xfer: processing %d messages:\n", num);
+ ret = pm_runtime_get_sync(dev->dev);
+ if (ret < 0)
+ goto out;
+
/*
* The hardware can handle at most two messages concatenated by a
* repeated start via it's internal address feature.
@@ -488,18 +494,21 @@ static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num)
if (num > 2) {
dev_err(dev->dev,
"cannot handle more than two concatenated messages.\n");
- return 0;
+ ret = 0;
+ goto out;
} else if (num == 2) {
int internal_address = 0;
int i;
if (msg->flags & I2C_M_RD) {
dev_err(dev->dev, "first transfer must be write.\n");
- return -EINVAL;
+ ret = -EINVAL;
+ goto out;
}
if (msg->len > 3) {
dev_err(dev->dev, "first message size must be <= 3.\n");
- return -EINVAL;
+ ret = -EINVAL;
+ goto out;
}
/* 1st msg is put into the internal address, start with 2nd */
@@ -523,7 +532,13 @@ static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num)
ret = at91_do_twi_transfer(dev);
- return (ret < 0) ? ret : num;
+ if (ret == 0)
I don't figure out why you've changed this condition.
Post by Wenyou Yang
+ ret = num;
+ pm_runtime_mark_last_busy(dev->dev);
+ pm_runtime_put_autosuspend(dev->dev);
+
+ return ret;
}
static u32 at91_twi_func(struct i2c_adapter *adapter)
@@ -795,11 +810,20 @@ static int at91_twi_probe(struct platform_device *pdev)
dev->adapter.timeout = AT91_I2C_TIMEOUT;
dev->adapter.dev.of_node = pdev->dev.of_node;
+ pm_runtime_set_autosuspend_delay(dev->dev, AUTOSUSPEND_TIMEOUT);
+ pm_runtime_use_autosuspend(dev->dev);
+ pm_runtime_set_active(dev->dev);
+ pm_runtime_enable(dev->dev);
+
rc = i2c_add_numbered_adapter(&dev->adapter);
if (rc) {
dev_err(dev->dev, "Adapter %s registration failed\n",
dev->adapter.name);
clk_disable_unprepare(dev->clk);
+
+ pm_runtime_disable(dev->dev);
+ pm_runtime_set_suspended(dev->dev);
+
return rc;
}
@@ -814,16 +838,19 @@ static int at91_twi_remove(struct platform_device *pdev)
i2c_del_adapter(&dev->adapter);
clk_disable_unprepare(dev->clk);
+ pm_runtime_disable(dev->dev);
+ pm_runtime_set_suspended(dev->dev);
+
return 0;
}
#ifdef CONFIG_PM
-
+#ifdef CONFIG_PM_RUNTIME
static int at91_twi_runtime_suspend(struct device *dev)
{
struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);
- clk_disable(twi_dev->clk);
+ clk_disable_unprepare(twi_dev->clk);
return 0;
}
@@ -832,12 +859,13 @@ static int at91_twi_runtime_resume(struct device *dev)
{
struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);
- return clk_enable(twi_dev->clk);
+ return clk_prepare_enable(twi_dev->clk);
}
+#endif
static const struct dev_pm_ops at91_twi_pm = {
- .runtime_suspend = at91_twi_runtime_suspend,
- .runtime_resume = at91_twi_runtime_resume,
+ SET_RUNTIME_PM_OPS(at91_twi_runtime_suspend,
+ at91_twi_runtime_resume, NULL)
};
#define at91_twi_pm_ops (&at91_twi_pm)
--
1.7.9.5
Regards
Ludovic
Wenyou Yang
2014-10-20 03:42:13 UTC
Permalink
Signed-off-by: Wenyou Yang <wenyou.yang-***@public.gmane.org>
---
drivers/i2c/busses/i2c-at91.c | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)

diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c
index 03b9f48..8f408f8 100644
--- a/drivers/i2c/busses/i2c-at91.c
+++ b/drivers/i2c/busses/i2c-at91.c
@@ -845,6 +845,35 @@ static int at91_twi_remove(struct platform_device *pdev)
}

#ifdef CONFIG_PM
+#ifdef CONFIG_PM_SLEEP
+static int at91_twi_suspend(struct device *dev)
+{
+ struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);
+
+ if (!pm_runtime_suspended(dev))
+ clk_disable_unprepare(twi_dev->clk);
+
+ return 0;
+}
+
+static int at91_twi_resume(struct device *dev)
+{
+ struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);
+ int ret;
+
+ if (!pm_runtime_suspended(dev)) {
+ ret = clk_prepare_enable(twi_dev->clk);
+ if (ret)
+ return ret;
+ }
+
+ pm_runtime_mark_last_busy(dev);
+ pm_request_autosuspend(dev);
+
+ return 0;
+}
+#endif
+
#ifdef CONFIG_PM_RUNTIME
static int at91_twi_runtime_suspend(struct device *dev)
{
@@ -864,6 +893,7 @@ static int at91_twi_runtime_resume(struct device *dev)
#endif

static const struct dev_pm_ops at91_twi_pm = {
+ SET_SYSTEM_SLEEP_PM_OPS(at91_twi_suspend, at91_twi_resume)
SET_RUNTIME_PM_OPS(at91_twi_runtime_suspend,
at91_twi_runtime_resume, NULL)
};
--
1.7.9.5
Ludovic Desroches
2014-10-20 12:42:42 UTC
Permalink
Post by Wenyou Yang
---
drivers/i2c/busses/i2c-at91.c | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c
index 03b9f48..8f408f8 100644
--- a/drivers/i2c/busses/i2c-at91.c
+++ b/drivers/i2c/busses/i2c-at91.c
@@ -845,6 +845,35 @@ static int at91_twi_remove(struct platform_device *pdev)
}
#ifdef CONFIG_PM
+#ifdef CONFIG_PM_SLEEP
+static int at91_twi_suspend(struct device *dev)
+{
+ struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);
+
+ if (!pm_runtime_suspended(dev))
+ clk_disable_unprepare(twi_dev->clk);
+
+ return 0;
+}
+
+static int at91_twi_resume(struct device *dev)
+{
+ struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);
+ int ret;
+
+ if (!pm_runtime_suspended(dev)) {
+ ret = clk_prepare_enable(twi_dev->clk);
+ if (ret)
+ return ret;
+ }
+
+ pm_runtime_mark_last_busy(dev);
+ pm_request_autosuspend(dev);
+
+ return 0;
+}
+#endif
+
#ifdef CONFIG_PM_RUNTIME
static int at91_twi_runtime_suspend(struct device *dev)
{
@@ -864,6 +893,7 @@ static int at91_twi_runtime_resume(struct device *dev)
#endif
static const struct dev_pm_ops at91_twi_pm = {
+ SET_SYSTEM_SLEEP_PM_OPS(at91_twi_suspend, at91_twi_resume)
SET_RUNTIME_PM_OPS(at91_twi_runtime_suspend,
at91_twi_runtime_resume, NULL)
};
--
1.7.9.5
Ludovic Desroches
2014-10-20 13:15:14 UTC
Permalink
Adding Kevin in the CC list since he had some comments about the PM
runtime support for the SPI driver.
Post by Wenyou Yang
---
drivers/i2c/busses/i2c-at91.c | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c
index 03b9f48..8f408f8 100644
--- a/drivers/i2c/busses/i2c-at91.c
+++ b/drivers/i2c/busses/i2c-at91.c
@@ -845,6 +845,35 @@ static int at91_twi_remove(struct platform_device *pdev)
}
#ifdef CONFIG_PM
+#ifdef CONFIG_PM_SLEEP
+static int at91_twi_suspend(struct device *dev)
+{
+ struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);
+
+ if (!pm_runtime_suspended(dev))
+ clk_disable_unprepare(twi_dev->clk);
+
+ return 0;
+}
+
+static int at91_twi_resume(struct device *dev)
+{
+ struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);
+ int ret;
+
+ if (!pm_runtime_suspended(dev)) {
+ ret = clk_prepare_enable(twi_dev->clk);
+ if (ret)
+ return ret;
+ }
+
+ pm_runtime_mark_last_busy(dev);
+ pm_request_autosuspend(dev);
+
+ return 0;
+}
+#endif
+
#ifdef CONFIG_PM_RUNTIME
static int at91_twi_runtime_suspend(struct device *dev)
{
@@ -864,6 +893,7 @@ static int at91_twi_runtime_resume(struct device *dev)
#endif
static const struct dev_pm_ops at91_twi_pm = {
+ SET_SYSTEM_SLEEP_PM_OPS(at91_twi_suspend, at91_twi_resume)
SET_RUNTIME_PM_OPS(at91_twi_runtime_suspend,
at91_twi_runtime_resume, NULL)
};
--
1.7.9.5
Kevin Hilman
2014-10-20 18:15:41 UTC
Permalink
Wenyou Yang <wenyou.yang-***@public.gmane.org> writes:

Add a changelog here describing what you're doing, and why.
Post by Wenyou Yang
---
drivers/i2c/busses/i2c-at91.c | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c
index 03b9f48..8f408f8 100644
--- a/drivers/i2c/busses/i2c-at91.c
+++ b/drivers/i2c/busses/i2c-at91.c
@@ -845,6 +845,35 @@ static int at91_twi_remove(struct platform_device *pdev)
}
#ifdef CONFIG_PM
+#ifdef CONFIG_PM_SLEEP
+static int at91_twi_suspend(struct device *dev)
+{
+ struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);
+
+ if (!pm_runtime_suspended(dev))
+ clk_disable_unprepare(twi_dev->clk);
I would just call at91_twi_runtime_suspend() here.

Then, if you need to add additional steps, you only have to add them in
once place. This also makes it obvious that ->suspend and
->runtime_suspend are doing the exact same thing.

NOTE: you'll need to wrap the runtime_suspend|resume functions in just
CONFIG_PM instead of CONFIG_PM_RUNTIME for this to work.

Kevin
Wenyou Yang
2014-10-20 03:42:14 UTC
Permalink
Amend the i2c at91 pin controller to optionally take a pin control
handle and set the state of the pins to:

- "default" on boot, resume and before performing an transfer
- "sleep" on suspend()

This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle

Signed-off-by: Wenyou Yang <wenyou.yang-***@public.gmane.org>
---
drivers/i2c/busses/i2c-at91.c | 12 +++++++++++-
1 file changed, 11 insertions(+), 1 deletion(-)

diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c
index 8f408f8..ed2c382 100644
--- a/drivers/i2c/busses/i2c-at91.c
+++ b/drivers/i2c/busses/i2c-at91.c
@@ -32,6 +32,7 @@
#include <linux/slab.h>
#include <linux/platform_data/dma-atmel.h>
#include <linux/pm_runtime.h>
+#include <linux/pinctrl/consumer.h>

#define DEFAULT_TWI_CLK_HZ 100000 /* max 400 Kbits/s */
#define AT91_I2C_TIMEOUT msecs_to_jiffies(100) /* transfer timeout */
@@ -748,6 +749,8 @@ static int at91_twi_probe(struct platform_device *pdev)
u32 phy_addr;
u32 bus_clk_rate;

+ pinctrl_pm_select_default_state(&pdev->dev);
+
dev = devm_kzalloc(&pdev->dev, sizeof(*dev), GFP_KERNEL);
if (!dev)
return -ENOMEM;
@@ -850,8 +853,10 @@ static int at91_twi_suspend(struct device *dev)
{
struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);

- if (!pm_runtime_suspended(dev))
+ if (!pm_runtime_suspended(dev)) {
clk_disable_unprepare(twi_dev->clk);
+ pinctrl_pm_select_sleep_state(dev);
+ }

return 0;
}
@@ -862,6 +867,7 @@ static int at91_twi_resume(struct device *dev)
int ret;

if (!pm_runtime_suspended(dev)) {
+ pinctrl_pm_select_default_state(dev);
ret = clk_prepare_enable(twi_dev->clk);
if (ret)
return ret;
@@ -881,6 +887,8 @@ static int at91_twi_runtime_suspend(struct device *dev)

clk_disable_unprepare(twi_dev->clk);

+ pinctrl_pm_select_sleep_state(dev);
+
return 0;
}

@@ -888,6 +896,8 @@ static int at91_twi_runtime_resume(struct device *dev)
{
struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);

+ pinctrl_pm_select_default_state(dev);
+
return clk_prepare_enable(twi_dev->clk);
}
#endif
--
1.7.9.5
Ludovic Desroches
2014-10-20 12:43:36 UTC
Permalink
Post by Wenyou Yang
Amend the i2c at91 pin controller to optionally take a pin control
- "default" on boot, resume and before performing an transfer
- "sleep" on suspend()
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle
---
drivers/i2c/busses/i2c-at91.c | 12 +++++++++++-
1 file changed, 11 insertions(+), 1 deletion(-)
diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c
index 8f408f8..ed2c382 100644
--- a/drivers/i2c/busses/i2c-at91.c
+++ b/drivers/i2c/busses/i2c-at91.c
@@ -32,6 +32,7 @@
#include <linux/slab.h>
#include <linux/platform_data/dma-atmel.h>
#include <linux/pm_runtime.h>
+#include <linux/pinctrl/consumer.h>
#define DEFAULT_TWI_CLK_HZ 100000 /* max 400 Kbits/s */
#define AT91_I2C_TIMEOUT msecs_to_jiffies(100) /* transfer timeout */
@@ -748,6 +749,8 @@ static int at91_twi_probe(struct platform_device *pdev)
u32 phy_addr;
u32 bus_clk_rate;
+ pinctrl_pm_select_default_state(&pdev->dev);
+
dev = devm_kzalloc(&pdev->dev, sizeof(*dev), GFP_KERNEL);
if (!dev)
return -ENOMEM;
@@ -850,8 +853,10 @@ static int at91_twi_suspend(struct device *dev)
{
struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);
- if (!pm_runtime_suspended(dev))
+ if (!pm_runtime_suspended(dev)) {
clk_disable_unprepare(twi_dev->clk);
+ pinctrl_pm_select_sleep_state(dev);
+ }
return 0;
}
@@ -862,6 +867,7 @@ static int at91_twi_resume(struct device *dev)
int ret;
if (!pm_runtime_suspended(dev)) {
+ pinctrl_pm_select_default_state(dev);
ret = clk_prepare_enable(twi_dev->clk);
if (ret)
return ret;
@@ -881,6 +887,8 @@ static int at91_twi_runtime_suspend(struct device *dev)
clk_disable_unprepare(twi_dev->clk);
+ pinctrl_pm_select_sleep_state(dev);
+
return 0;
}
@@ -888,6 +896,8 @@ static int at91_twi_runtime_resume(struct device *dev)
{
struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);
+ pinctrl_pm_select_default_state(dev);
+
return clk_prepare_enable(twi_dev->clk);
}
#endif
--
1.7.9.5
Kevin Hilman
2014-10-20 18:17:43 UTC
Permalink
Post by Wenyou Yang
Amend the i2c at91 pin controller to optionally take a pin control
- "default" on boot, resume and before performing an transfer
- "sleep" on suspend()
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle
This patch is a good example of why you should just have the ->suspend
function call the same function as ->runtime_suspend.

If you do that, rather than having to add the pinctrl_pm* calls bo both
system PM and runtime PM functions, you could've just added them to the
runtime PM functions.

Kevin

Continue reading on narkive:
Loading...